Topic Last Modified: 2013-01-16

Use the Set-PublicFolderMoveRequest cmdlet to change a public folder move request after the move request has been created. You can use the Set-PublicFolderMoveRequest cmdlet to recover from a failed move request.

For information about the parameter sets in the Syntax section below, see Syntax.

Syntax

Set-PublicFolderMoveRequest -Identity <PublicFolderMoveRequestIdParameter> [-AcceptLargeDataLoss <SwitchParameter>] [-BadItemLimit <Unlimited>] [-BatchName <String>] [-CompletedRequestAgeLimit <Unlimited>] [-LargeItemLimit <Unlimited>] [-Priority <Lowest | Lower | Low | Normal | High | Higher | Highest | Emergency>] [-Confirm [<SwitchParameter>]] [-DomainController <Fqdn>] [-SuspendWhenReadyToComplete <$true | $false>] [-WhatIf [<SwitchParameter>]]

Examples

EXAMPLE 1

This example changes the public folder move request \PublicFolderMove to accept up to five corrupted public folder items.

Copy Code 
Set-PublicFolderMoveRequest -Identity \PublicFolderMove -BadItemLimit 5

Detailed Description

You can pipeline the Set-PublicFolderMoveRequest cmdlet from the Get-PublicFolderMoveRequestStatistics or Get-PublicFolderMoveRequest cmdlet.

You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Public folders" entry in the Sharing and Collaboration Permissions topic.

Parameters

Parameter Required Type Description

Identity

Required

Microsoft.Exchange.Management.RecipientTasks.PublicFolderMoveRequestIdParameter

The Identity parameter specifies the identity of the public folder move request. The default identity of a public folder move request is \PublicFolderMove.

AcceptLargeDataLoss

Optional

System.Management.Automation.SwitchParameter

The AcceptLargeDataLoss parameter specifies that a large amount of data loss is acceptable if the BadItemLimit parameter is set to 51 or higher. Items are considered corrupted if the items can't be read from the source mailbox or can't be written to the target mailbox. Corrupted items won't be available in the destination mailbox.

BadItemLimit

Optional

Microsoft.Exchange.Data.Unlimited

The BadItemLimit parameter specifies the number of bad items to skip if the request encounters corruption in the mailbox. Use 0 to not skip bad items. The valid input range for this parameter is from 0 through 2147483647. The default value is 0. We recommend that you keep the default value 0 and only change the BadItemLimit parameter value if the request fails.

Note:
If you set the BadItemLimit parameter to more than 50, the command fails, and you receive a warning stating: "Please confirm your intention to accept a large amount of data loss by specifying AcceptLargeDataLoss." If you receive this warning, you need to run the command again, this time using the AcceptLargeDataLoss parameter. No further warnings appear, and any corrupted items aren't available after the process is complete.

BatchName

Optional

System.String

The BatchName parameter specifies a different name for a batch.

CompletedRequestAgeLimit

Optional

Microsoft.Exchange.Data.Unlimited

The CompletedRequestAgeLimit parameter specifies how long the request is kept after it has completed before being automatically removed. The default CompletedRequestAgeLimit parameter value is 30 days.

Confirm

Optional

System.Management.Automation.SwitchParameter

The Confirm switch can be used to suppress the confirmation prompt that appears by default when this cmdlet is run. To suppress the confirmation prompt, use the syntax -Confirm:$False. You must include a colon ( : ) in the syntax.

DomainController

Optional

Microsoft.Exchange.Data.Fqdn

The DomainController parameter specifies the fully qualified domain name (FQDN) of the domain controller that writes this configuration change to Active Directory.

LargeItemLimit

Optional

Microsoft.Exchange.Data.Unlimited

The LargeItemLimit parameter specifies the number of large items to skip if the request encounters such items in the public folder. Use 0 to not skip any large items. If any number above 50 is specified, the AcceptLargeDataLoss parameter must also be specified. The default value is 0. We recommend that you use the default value of 0 and increase the LargeItemLimit only when large items are encountered.

Priority

Optional

Microsoft.Exchange.MailboxReplicationService.RequestPriority

The Priority parameter specifies the order in which this request should be processed in the request queue. Requests are processed in order, based on server health, status, priority, and last update time.

SuspendWhenReadyToComplete

Optional

System.Boolean

The SuspendWhenReadyToComplete parameter specifies whether to suspend the request before it reaches the status of CompletionInProgress. After the move is suspended, it has a status of AutoSuspended. You can then manually complete the move by using the Resume-PublicFolderMoveRequest command.

WhatIf

Optional

System.Management.Automation.SwitchParameter

The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch.

Input Types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.

Return Types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.