Applies to: Exchange Server 2013, Exchange Online
Topic Last Modified: 2012-07-06
Use the Set-HybridMailflow cmdlet to configure the message transport settings for the Microsoft Exchange Online Protection (EOP) service in a hybrid deployment.
 Important: |
|---|
| The Set-HybridMailflow cmdlet is only used to support hybrid deployments configured with the Hybrid Configuration wizard offered in Microsoft Exchange Server 2010 Service Pack 2 (SP2). |
For information about the parameter sets in the Syntax section below, see Syntax.
Syntax
Set-HybridMailflow [-CentralizedTransportEnabled
<$true | $false>] [-CertificateSubject <String>]
[-Confirm [<SwitchParameter>]] [-InboundIPs
<IPRange[]>] [-OnPremisesFQDN <Fqdn>] [-Organization
<OrganizationIdParameter>] [-OutboundDomains
<SmtpDomainWithSubdomains[]>] [-SecureMailEnabled <$true |
$false>] [-WhatIf [<SwitchParameter>]]
|
Examples
EXAMPLE 1
This example configures the message transport settings in the EOP service for a hybrid deployment.
 Copy Code |
|
|---|---|
Set-HybridMailflow |
|
Detailed Description
The Set-HybridMailflow cmdlet supports the configuration of message transport settings for hybrid deployments created with the Hybrid Configuration wizard offered in Exchange 2010 SP2. This cmdlet isn't typically used by administrators; therefore, we strongly recommend that it only be used as part of the hybrid configuration process using the Hybrid Configuration wizard.
You need to be assigned permissions before you can run this cmdlet. Although all parameters for this cmdlet are listed in this topic, you may not have access to some parameters if they're not included in the permissions assigned to you. To see what permissions you need, see the "Hybrid deployment configuration" entry in the Exchange and Shell Infrastructure Permissions topic.
Parameters
| Parameter | Required | Type | Description |
|---|---|---|---|
|
CentralizedTransportEnabled |
Optional |
System.Boolean |
The CentralizedTransportEnabled parameter specifies that
the Exchange Online organization routes all outbound mail messages
to external recipients to the on-premises Exchange organization.
The on-premises Exchange organization then routes the messages to
the external recipients. The valid input for the
CentralizedTransportEnabled parameter is |
|
CertificateSubject |
Optional |
System.String |
The CertificateSubject parameter specifies the principal name of the certificate used for secure mail flow between the on-premises Exchange and Exchange Online organizations. |
|
Confirm |
Optional |
System.Management.Automation.SwitchParameter |
The Confirm switch causes the command to pause processing and requires you to acknowledge what the command will do before processing continues. You don't have to specify a value with the Confirm switch. |
|
InboundIPs |
Optional |
Microsoft.Exchange.Data.IPRange[] |
The InboundIPs parameter specifies the IP addresses of the on-premises mail transport servers configured as part of the hybrid deployment. These must point to either Exchange 2010 SP2 Hub Transport or Edge Transport servers. |
|
OnPremisesFQDN |
Optional |
Microsoft.Exchange.Data.Fqdn |
The OnPremisesFQDN parameter specifies the fully qualified domain name (FQDN) of the outbound smart host in the on-premises Exchange organization to use for centralized transport. This is either an on-premises Exchange 2010 SP2 Hub Transport or Edge Transport server. |
|
Organization |
Optional |
Microsoft.Exchange.Configuration.Tasks.OrganizationIdParameter |
The Organization parameter is reserved for internal Microsoft use. |
|
OutboundDomains |
Optional |
Microsoft.Exchange.Data.SmtpDomainWithSubdomains[] |
The OutboundDomains parameter specifies SMTP domains configured for the hybrid deployment. |
|
SecureMailEnabled |
Optional |
System.Boolean |
The SecureMailEnabled parameter specifies that all
messages sent between the on-premises Exchange and the Exchange
Online organizations must use the Transport Layer Security (TLS)
protocol and the assigned digital certificate. The valid input for
the SecureMailEnabled parameter is |
|
WhatIf |
Optional |
System.Management.Automation.SwitchParameter |
The WhatIf switch instructs the command to simulate the actions that it would take on the object. By using the WhatIf switch, you can view what changes would occur without having to apply any of those changes. You don't have to specify a value with the WhatIf switch. |
Input Types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn’t accept input data.
Return Types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn’t return data.