Applies to: Exchange Server 2013, Exchange Online
Topic Last Modified: 2012-10-05
By default, the two IMAP4 services, the Microsoft Exchange IMAP4 service and the Microsoft Exchange IMAP4 Backend service, aren’t started on computers running Microsoft Exchange Server 2013. You must start these two services to allow your email clients to connect to Exchange using IMAP4. When these services are running, Exchange 2013 accepts unsecured IMAP4 client communications on port 143 and over port 993 using Secure Sockets Layer (SSL).
The Microsoft Exchange IMAP4 service runs on Exchange 2013 computers that are running the Client Access server role. The Microsoft Exchange IMAP4 Backend service runs on the Exchange 2013 computer that’s running the Mailbox server role. In environments where the Client Access and Mailbox server roles are running on the same computer, you manage both services on the same computer.
For additional information related to POP3 and IMAP4, see POP3 and IMAP4.
What do you need to know before you begin?
- Estimated time to complete: 2 minutes.
- You need to be assigned permissions before you can perform this
procedure or procedures. To see what permissions you need, see the
"POP3 and IMAP4 Permissions" section in the Clients and Mobile
Devices Permissions topic.
- For information about keyboard shortcuts that may apply to the
procedures in this topic, see Keyboard Shortcuts in
the Exchange Admin Center.
Tip: |
---|
Having problems? Ask for help in the Exchange forums. Visit the forums at: Exchange Server, Exchange Online, or Exchange Online Protection. |
What do you want to do?
Use the Microsoft Management Console Services snap-in to start or stop the IMAP4 services
To start the IMAP4 services:
- On the computer running the Client Access server role, click
Start, point to Programs, point to Administrative
Tools, and then click Services. Right-click Microsoft
Exchange IMAP4, and then click Start.
- On the computer running the Mailbox server role, click
Start, point to Programs, point to Administrative
Tools, and then click Services. Right-click Microsoft
Exchange IMAP4 Backend, and then click Start.
To stop the IMAP4 services:
- On the computer running the Client Access server role, click
Start, point to Programs, point to Administrative
Tools, and then click Services. Right-click Microsoft
Exchange IMAP4, and then click Stop.
- On the computer running the Mailbox server role, click
Start, point to Programs, point to Administrative
Tools, and then click Services. Right-click Microsoft
Exchange IMAP4 Backend, and then click Stop.
Use the Shell to start or stop the IMAP4 services
To start the IMAP4 services:
- On the computer running the Client Access server role, from the
Shell, run the following command to start the Microsoft Exchange
IMAP4 service.
Copy Code Start-service msExchangeIMAP4
- On the computer running the Mailbox server role, from the
Shell, run the following command to start the Microsoft Exchange
IMAP4 Backend service.
Copy Code Start-service msExchangeIMAP4BE
To stop the IMAP4 services:
- On the computer running the Client Access server role, from the
Shell, run the following command to stop the Microsoft Exchange
IMAP4 service.
Copy Code Stop-service msExchangeIMAP4
- On the computer running the Mailbox server role, from the
Shell, run the following command to stop the Microsoft Exchange
IMAP4 Backend service.
Copy Code Stop-service msExchangeIMAP4BE
Use net start to start or stop the IMAP4 services
To start the IMAP4 services:
- On the computer running the Client Access server role, at the
command prompt, run the following command to start the Microsoft
Exchange IMAP4 service.
Copy Code net start msExchangeIMAP4
- On the computer running the Mailbox server role, at the command
prompt, run the following command to start the Microsoft Exchange
IMAP4 Backend service.
Copy Code net start msExchangeIMAP4BE
To stop the IMAP4 services:
- On the computer running the Client Access server role, at the
command prompt, run the following command to stop the Microsoft
Exchange IMAP4 service.
Copy Code Net Stop MSExchangeIMAP4
- On the computer running the Mailbox server role, at the command
prompt, run the following command to stop the Microsoft Exchange
IMAP4 Backend service.
Copy Code Net Stop MSExchangeIMAP4BE
How do you know this worked?
- On the Exchange Client Access server, open Windows Task
Manager. On the Services tab, the status for
MSExchangeIMAP4 will show as Running if the Microsoft
Exchange IMAP4 service is running.
- On the Exchange Mailbox server, open Windows Task Manager. On
the Services tab, the status for MSExchangeIMAP4BE
will show as Running if the Microsoft Exchange IMAP4 Backend
service is running.