The following topologies are supported:

• Exchange 2007 Hub Transport server role in an Exchange Server 2003 infrastructure
  
  
• Exchange 2007 Hub Transport server role in an Exchange 2000 Server infrastructure
  
  
• Exchange 2007 Hub Transport server role deployed on separate hardware
  
  
• Exchange 2007 Hub Transport server role hosted on the same hardware as other server roles
  
  

Note:
You cannot install the Hub Transport server role on a server that is configured as part of a cluster.

To complete mail flow configuration for the Exchange organization and to send and receive e-mail to and from the Internet, you must configure Send connectors and Receive connectors that enable at least one Hub Transport server to connect to the Internet. You can configure Internet connectivity for a Hub Transport by using any of the following methods:

• You can deploy an Edge Transport server and subscribe it to the Exchange organization. This is the recommended deployment method. By default, when you create the Edge Subscription, the required Send connectors are automatically created. You do not have to modify the configuration of the default Receive connector on the Hub Transport server for this scenario.
  
  
• You can send and receive Internet e-mail by relaying through Microsoft Exchange Hosted Services or another third-party Simple Mail Transfer Protocol (SMTP) gateway server. In this scenario, you have to create a Send connector and a Receive connector between the Hub Transport server and the external SMTP servers that process and route Internet e-mail.
  
  
• You can establish Internet mail flow directly through a Hub Transport server. In this scenario, you have to create a Send connector that routes e-mail to the Internet. Also, you have to modify the configuration of the default Receive connector to accept anonymous e-mail submissions. In this scenario, the Exchange 2007 Hub Transport server can be reached directly through the Internet. We don't recommend this topology because it increases security risks by exposing to the Internet the Exchange 2007 server and all roles installed on that server. We recommend that you implement a perimeter network-based SMTP gateway, such as the Edge Transport server, instead.
  
  Note   You can install the anti-spam agents on the Hub Transport server role by using the Install-AntiSpamAgents.ps1 script. This script is located in the <system drive>/Program Files/Microsoft/Exchange Server/Scripts folder. After you run this script, all the anti-spam agents are installed and enabled, and the Anti-spam tab is available in the Exchange Management Console for Hub Transport servers. We recommend that you install the anti-spam agents if you select this topology so that the Hub Transport server can provide anti-spam protection for the Exchange organization.
  
  

Important:

If you configure an Internet-facing Hub Transport server, you cannot configure a Send connector to attach a particular IP address to messages that are sent from the Hub Transport server. For example, if more than one IP address is assigned to the Hub Transport server, you cannot select which IP address is used by a Send connector to relay e-mail to the Internet. If you use an SMTP relay, such as an Edge Transport server, the IP address of that computer is affixed as the message source.

For more information, see Configuring Hub Transport Server Connectors and How to Configure Connectors for Internet Mail Flow.

You configure fault tolerance and load balancing for Hub Transport servers when you install more than one Hub Transport server in the same Active Directory site. By default, connections to Hub Transport servers are automatically load balanced if more than one Hub Transport server is deployed in an Active Directory site. If one Hub Transport server is unavailable, the operational Hub Transport servers continue to accept connections. If all Hub Transport servers in an Active Directory site are unavailable, messages are queued until a Hub Transport server becomes available or the messages expire.

Load balancing of outbound connections to remote domains is achieved by specifying more than one Hub Transport server in the same Active Directory site as a source server for the Send connector. Load balancing does not occur when the source servers for a Send connector are located in different Active Directory sites.

Note:
If the Hub Transport server is installed on the same hardware as the Mailbox server role, load balancing may not occur. When the Hub Transport server role is on the same hardware as the Mailbox server role, the local server is preferred for all messages that are sent by users who have mailboxes on that server. Therefore, in this scenario, true load balancing does not occur.

For more information, see Load Balancing and Fault Tolerance for Transport Servers.

You cannot install the Hub Transport server role on the same hardware as the Mailbox server role when the Mailbox server role is deployed in a cluster. However, we support deployment of the Hub Transport server role on the same hardware as the Client Access server role.

New in Exchange 2007 Service Pack 1

For more information, see the following topics:

• Planning for Coexistence
  
  
• Planning Your Deployment
  
  
• Understanding Active Directory Site-Based Routing
  
  
• High Availability