The UM Troubleshooting Tool simplifies testing and troubleshooting in UM deployments. When the UM Troubleshooting Tool is run, it automatically generates a set of trace files that are stored in the C:\Users\%UserProfile%\AppData\Roaming\Microsoft Exchange 2010 UM Troubleshooting folder. The following trace files are generated by the tool:

• UMTool_Collaboration   Includes RTC stack traces.
  
  
• UMTool_DiagnosticLog   Lists all the tests that are run and their results.
  
  
• UMTool_S4   Includes the S4: signaling stack traces.
  
  
• UMTool_SIPMessageLogs   Includes the full SIP traces for the test call that's made.
  
  

The UM Troubleshooting Tool connects directly to an on-premises Session Border Controller (SBC), if one exists, or connects to an SBC in a datacenter and emulates an incoming call as if the call was coming from a PBX through an IP gateway or an IP PBX. The UM Troubleshooting tool can be used to diagnose:

• Incorrect settings in on-premises or cross-premises UM deployments in which Office Communications Server R2 or Microsoft Lync Server 2010 is deployed.
  
  
• Incorrect settings on on-premises or cross-premises telephony equipment that includes IP gateways and PBXs or IP PBXs.
  
  
• Issues with Domain Name System (DNS).
  
  
• Certificate issues when you're using SIP secured or Secured UM dial plans.
  
  
• Signaling and media issues for DTMF (also known as touchtone) and audio.
  
  

If the UM Troubleshooting Tool detects a failure in your configuration, the tool reports the reason for the error and the possible solutions for the issues that have been detected. The errors that can be reported when the UM Troubleshooting Tool is used in an on-premises deployment include the following:

• The maximum call limit has been reached.
  
  
• The user isn't enabled for Unified Messaging.
  
  
• The UM IP gateway, dial plan, or hunt group information can't be located.
  
  
• The security type doesn't match the UM dial plan.
  
  
• There are no worker processes available to process the call.
  
  
• The UM server is disabled.
  
  
• The Active Directory forest couldn't be located.
  
  
• No disk space is available.
  
  
• Invalid SIP headers were used in the request.
  
  
• A call was made to an Office Communications Server 2007 R2 server or Lync Server server.
  
  
• The UM IP gateway is disabled.
  
  
• The URI for the user who is being called isn't valid.
  
  

When the UM Troubleshooting Tool is used in a cross-premises deployment, the errors that can be reported include the following:

• The user isn't enabled for Unified Messaging.
  
  
• The UM IP gateway is disabled.
  
  
• The URI for the user is invalid.
  
  
• The security type doesn't match the UM dial plan.
  
  
• Invalid SIP headers were used in the request.
  
  
• The UM IP gateway, dial plan, or hunt group information can't be located.
  
  

The UM Troubleshooting Tool sends a sample wav file for 15 seconds. After the audio file and RTP audio stream is sent and played back, the tool reports general audio quality metrics for diagnosing audio quality issues related to network connectivity, such as jitter and average packet loss. These reports include the media stream quality to and from a UM server and contain the following:

• Network Mean Opinion Score (NMOS)
  
  
• Codec
  
  
• Latency in milliseconds (ms)
  
  
• Jitter in milliseconds (ms)
  
  
• % of packet loss
  
  
• The NMOS classification and rating that will be used to determine the audio quality will be:
  
  
• NMOS less than 2 = Poor
  
  
• NMOS greater than 2 but less than 3 = Average
  
  
• NMOS greater than 3 but less than 4 = Good
  
  
• NMOS greater than 4 but less than 5 = Excellent
  
  

The UM Troubleshooting Tool supports testing UM dial plans that use Secured, SIP Secured, and Unsecured calls. If you choose Secured or SIP Secured, the thumbprint of the certificate that's used is checked to determine whether the certificate is expired and the type of certificate that's used for TLS (Transport Layer Security) communications. The certificate is used to correctly identify and ensure the identity of the remote computer. When Secured or SIP Secured mode is selected, the UM Troubleshooting Tool verifies whether the following are true:

• The local certificate was found in the local computer store.
  
  
• The certificate being used is trusted.
  
  
• The target name specified in the certificate is valid.
  
  
• The certificate has expired.
  
  
• The remote computer trusts the certificate.
  
  
• The certificate has been revoked.
  
  
• The certificate doesn't have the required enhanced key usage.
  
  

The UM Troubleshooting Tool can be run in either Gateway or SIPClient mode, depending on whether Office Communications Server 2007 R2 or Lync Server 2010 is deployed or whether IP gateways and PBXs or IP PBXs are used with Unified Messaging servers. When either Gateway or SIPClient mode is used, the UM Troubleshooting Tool supports making calls using the following formats. The format that's used depends on the URI type of the UM dial plan:

• Telephone extension   425-555-1010
  
  
• E.164 phone numbers   +1 (425) 555-1010
  
  
• SIP addresses   tonysmith@contoso.com
  
  

When SIPClient mode is used, the UM Troubleshooting Tool makes a voice memo call. This is a call that doesn't ring a phone or a Unified Communications (UC) endpoint. Instead, it sends the call directly to voice mail. When the UM Troubleshooting Tool is run in SIPClient mode, it will determine:

• Which target user is being called.
  
  
• Whether the SIP call was established successfully.
  
  

Whether the SIP call was accepted by an Exchange Unified Messaging server.

• Whether the correct DTMF sequence was received.
  
  
• Whether the diagnostic .wav file was sent and received by a UM server.
  
  
• The metrics that were used when the media or audio quality stream was received.
  
  

The UM Troubleshooting Tool emulates incoming calls and runs a series of diagnostic tests that help on-premises administrators and tenant administrators test call flow for call answering and identify configuration errors. Although the UM Troubleshooting Tool can be used in call answering scenarios, it can't be used to test the following types of calls:

• Outlook Voice Access calls, including calls that access voice mail, e-mail, calendar, the directory, personal Contacts, or personal options
  
  
• UM auto attendants
  
  
• Play on Phone
  
  
• Call Answering Rules
  
  
• Faxing
  
  
• Prompt provisioning
  
  

Return to top

Although the UM Troubleshooting Tool can help you troubleshoot, diagnose, and repair configuration issues in a cross-premises deployments, you can also used it in on-premises Unified Messaging deployments. In cross-premises deployments, the tool also validates on-site SBC configurations. The administrator can test all the Unified Messaging components that are used by Unified Messaging, including the SBCs. The following figure shows an overview of the components that can be tested in a cross premises deployment that includes on-site IP gateways and a local SBC that connects to an off-site SBC.

In the following example, Gateway mode is used to test call flow in an environment that doesn't include Office Communications Server 2007 R2 or Lync Server 2010. This example tests the telephony equipment, including IP gateways, PBXs and IP PBXs, and the Unified Messaging components. This example sets the Voice over IP (VoIP) security mode to Unsecured, uses the IP address 10.1.1.1 as the next hop, and includes an extension number in the diversion information.

	Copy Code
Test-ExchangeUMCallFlow -Mode Gateway -VoIPSecurity Unsecured -NextHop 10.1.1.1 -Diversion 12345

The following figure shows the components that are tested when Gateway mode is used.

Return to top

The UM Troubleshooting Tool can be used in on-premises or cross-premises deployments that include Office Communications Server 2007 R2 or Microsoft Lync Server 2010 when SIPClient mode is set. The following example uses SIPClient mode and tests the call flow with a secured UM dial plan in an environment that contains Office Communications Server 2007 R2 or Lync Server 2010 servers. By default, when you run the UM Troubleshooting Tool, it uses the credentials of the user who is currently logged on to the computer. When you run the following example, you’ll be prompted for the credentials you want to use when you run the UM Troubleshooting Tool. For details, see Set the Credentials to Use with the Exchange 2010 UM Troubleshooting Tool.

	Copy Code
Test-ExchangeUMCallFlow -Mode SIPClient -VoIPSecurity Secured -CallingParty tony@contoso.com -CalledParty david@contoso.com -Credential $get

The following figure shows the components that are tested when SIPClient mode is used.

The UM Troubleshooting Tool can be installed on a local Unified Messaging server or on another 64-bit computer running either:

• The Windows 7 or Windows Vista operating systems.
  
  
• The Windows Server 2008 or Windows Server 2008 R2 operating systems.
  
  

If you're using the UM Troubleshooting Tool on a 64-bit version of Windows 7, Windows Vista, or the 64-bit edition of Windows Server 2008, the following components must be installed before you can install the UM Troubleshooting Tool:

• Microsoft .NET Framework 3.5 Service Pack 1 (SP1)   See Microsoft .NET Framework 3.5 Service Pack 1.
  
  

  Note:
  If the tool will be run on a Windows Vista or Windows Server 2008 computer, see Microsoft .NET Framework 3.5 Family Update for Windows Vista x64, and Windows Server 2008 x64.

• Windows Remote Management (WinRM) 2.0 and Windows PowerShell V2 (Windows6.0-KB968930.msu)   See Microsoft Knowledge Base article 968930, Windows Management Framework Core package (Windows PowerShell 2.0 and WinRM 2.0).
  
  
• Microsoft Unified Communications Managed API 2.0 Core Runtime (UcmaRuntimeWebDownloadX64.msi)   See Unified Communications Managed API 2.0, Core Runtime (64-bit).
  
  

The UM Troubleshooting Tool (Test-ExchangeUMCallFlow cmdlet) isn't included on the Exchange 2010 SP1 DVD or the download that only includes Exchange 2010. However you can download the UM Troubleshooting Tool from the Microsoft Download Center.

For details, see Install the Exchange 2010 UM Troubleshooting Tool.

Return to top

The following table includes the parameters you can use with the Test-ExchangeUMCallFlow cmdlet and descriptions of those parameters. You can also use the Shell command Get-help Test-ExchangeUMCallFlow -detailed to find detailed information about each parameter that can be used with the Test-ExchangeUMCallFlow cmdlet, along with usage examples.

Parameters

Return to top